Product Series Easy Altivar 610 Product or component type variable speed drive Product Special Application Fan, Pump, Compressor, Conveyor Product Group ATV610 Model standard type Product Arrival Place Asynchronous Motors Synchronous motors Assembly board assembly EMC Filter Integrated 'Compatibly 61800-3 Category C3ile 50 M Motor Cable Maks IP protection degree IP20 Type of cooling forced convection Feeding frequency 50 ... 60 Hz -5 Network Phase Number 3 Phase [US] Nominal Nutrition Voltage 380 ... 460 V - 15 ... 10 Normal requirement for motor power kW 5.5 kW Heavy condition for 4 kW Normal requirement for motor power HP 7.5 hp Heavy condition for 5 HP Line flow 11.6 A -de 380 V (Normal condition) 10.5 A -DE 460 V (normal condition) 8.9 A -DE 380 V (heavy condition) 7.9 A -DE 460 V (heavy condition) possible line ISC 22 ka The visible power 8.4 kVA -460 V (normal condition) 460 V (heavy condition) in 6.3 kva Continuous output current 12.7 a -de 4 kHz for normal condition Heavy condition for 9.3 a -de 4 kHz Maximum Temporary Current 60 S (Normal) 60 s (heavy condition) during 14 A asynchronous motor control profile optimum moment mode Variable moment standard Fixed torque standard Output Frequency 0.1 500 Hz Nominal Switching Frequency 4 KHz Switching frequency 2 ... 12 khz adjustable NUMBER OF PRESSET SPEEDS 16 PREPRETE SPEED Communication Port Protocol Modbus Series Option Card Nest A: Communication Card, Profibus DP v1 Nest A: Digital or Analog G ç Expansion Card Yuva A: Relay output card Output voltage power feeding voltage Motor slip compensation automatically all kinds of loads Adjustable Continuous magnetic engine law is not available Compressible acceleration and slowdown ramps can be adjusted separately between 0.01 - 9000 seconds S, U or customized With DC Injection until it stops Protection Type Thermal Protection: Motor Motor Phase Cutting: Motor Thermal protection: driver Overheating: Driver Over Current Between Output Phase and Earth: Driver Overload of the output voltage: Driver Short Circuit Protection: Driver Motor Phase Cutting: Driver Excessive voltages in DC data: Driver Line Feeding Excess Tension: Driver Low Feeding Low Voltage: Driver Line Feeding Phase Loss: Driver Excessive Speed: Driver Cutting in the control circuit: drive Frequency resolution screen unit: 0.1 Hz Analog Login: 0.012 50 Hz Electric connection control, screw terminal: 0.5 ... 1.5 mm² Line side, screw terminal: 2.5 ... 16 mm² Motor, Screw Terminal: 2.5 ... 16 mm² Modbus Series for Type 1 RJ45 of the Connector (on Remote Graphic Terminal) Physical interface 2 -wire RS 485 Modbus Series Transmission Framework Modbus Series for RTU Transmission Speed ​​4.8, 9.6, 19.2, 38.4 kbit Sn Modbus Series Modbus series for polarization type impedance Number of Addresses 1 247 Modbus Series Access Method Slave External Feeding for Nutrition Digital Inputs: 24 V DC (19 30 V), 1.25 MA, Protection Type: Overload and Short Circuit Protection Internal feeding for reference potentiometer (1 - 10 kohm): 10,5 V DC - 5, 10 MA, protection type: overload and short circuit protection Local Signaling Local Diagnostic: 2 LED Internal Communication Status: 1 LED (Yellow) Communication Module Status: 2 LED (Two Color) Existence of Tension: 1 LED (Red) Width 145 mm Height 297 mm 350 mm EMC plate Depth 203 mm Product weight 4,575 kg Number of analog inputs 3 Analog input Type AI1, AI2, AI3 Software-Recruitable Voltage: 0 ... 10 V DC, Impedance: 30 Kohm, resolution 12 bit AI1, AI2, AI3 Software-Related Current: 0 ... 20 MA, Impedance: 250 OHM, resolution 12 bit AI2, AI3 SOFTWARE-CONFIGURABLE TEMPERATURE PROBE OR WATER LEVEL Sensor Number of digital inputs 6 Digital Input Type DI1 ... DI6 Programmable as Logic Input, 24 V DC (30 V), Impedance: 3.5 Kohm DI5, DI6 Programmable as a coup entrance: 0 30 kHz, 24 V dc (30 V) Introduction Compatibility DI1 ... DI6: Logic Entry Level 1 PLC DI5, DI6: Coup Entrance Level 1 PLC Digital Introduction Logic Positive Logic (Source): DI1 ... DI6 configurable Ir logic input, 5 V (status 0), 11 V (status 1) Negative Logic (Block): DI1 ... DI6 Configurated Logic Input, 16 V (Status 0), 10 V (Status 1) Positive Logic (Source): DI5, DI6 configurable coup input, 0.6 V (status 0), 2.5 V (status 1) analog output number 2 Analogue output type software-expulusable current AQ1, AQ2: 0 ... 20 MA, resolution 10 bit Software-Released Voltage AQ1, AQ2: 0 ... 10 V DC Impedance 470 ohm, resolution 10 bit Sampling time 5 ms - 0.1 msn (AI1, AI2, AI3) - analog input 2 ms - 0.5 msn (DI1 ... DI6) can be configured - digital entry 5 ms - 1 ms (DI5, DI6) can be configured - coup entrance 10 ms - 1 ms (AQ1, AQ2) - Analog output Accuracy - 0.6 AI1, AI2, AI3 60 C analog input for temperature change - 1 AQ1, AQ2 60 C analog output for temperature change linearity error AI1, AI2, AI3: Analog input for maximum value - 0.15 AQ1, AQ2: - Analog output for 0.2 Relay Outputs Number 3 Relay output type configurable relay Lojiki R1: Electrical durability of error relay 100000 Cycles Configurable Relay Lojiki R2: Electrical resistance to Sequence Relay 100000 Cycles Configurable Relay Logiki R3: Electrical resistance to Sequence Relay 100000 Cycles Renewal time relay output (R1, R2, R3): 5 ms ( - 0.5 msn) Minimum switching current relay output R1, R2, R3: 5 MA -DE 24 V DC Maximum switching current relay output R1, R2, R3 resistant load, cos phi 1: 3 a -de 250 V AC Relay output R1, R2, R3 resistant load, cos phi 1: 3 a -de 30 V dc Relay output R1, R2, R3 inductive load, cos phi 0.4 and l r 7 ms: 2 A -de 250 V AC Relay output R1, R2, R3 inductive load, cos phi 0.4 and l r 7 ms: 2 a -de 30 V dc Terminals between insulation power and control Insulation resistance 1 MOHM for 1 minute for grounding 500 V DC